Artigo Acesso aberto Produção Nacional

Simulação de Rompimento da Barragem São Bento do Una através do Software HEC-RAS

2022; UNIVERSIDADE FEDERAL DE PERNAMBUCO; Volume: 15; Issue: 2 Linguagem: Português

10.26848/rbgf.v15.2.p856-871

ISSN

1984-2295

Autores

Joao Pedro do Nascimento Silva, Maria Isabela Marques da Cunha Vieira Bello, Tiago Barbosa da Silva, Wesley Michael Pereira Silva,

Tópico(s)

Tailings Management and Properties

Resumo

Os danos associados ao rompimento de uma barragem são enormes, e devem ser evitados a todo custo, já que pode causar perdas de vidas humanas. Diversos estudos são realizados antes de sua construção a fim de evitar futuros desastres, dentre eles, destaca-se a determinação das áreas afetadas por um rompimento hipotético da barragem. Este artigo apresenta o resultado da simulação de ruptura da Barragem São Bento do Una, localizada no município de mesmo nome no interior de Pernambuco, por meio do modelo unidimensional de fluxo não permanente. Foi usada como base a geometria da área de estudo, elaborada por meio do software QGIS através da análise dos modelos digitais de terreno, disponibilizados pelo Programa Pernambuco Tridimensional (PE3D), e exportada para o software HEC-RAS. A partir dos resultados, foi determinada a região afetada, a vazão da água e profundidade, e foram criados mapas a fim de contribuir nos estudos para planos de contingência e mitigação de riscos. Verificou-se que o tempo decorrido para que a ruptura atingisse sua geometria final foi de 56 minutos após o início da simulação. A maior vazão de saída do reservatório aconteceu no minuto 56, onde 6672,72 m³/s de água são expelidos para fora do reservatório, diminuindo na medida que o nível d’água se aproxima da cota inferior da brecha de ruptura. O tempo gasto pela água para atingir a cidade de São Bento do Una, situada a cerca de 17 km da barragem, foi de aproximadamente 1 hora e 50 minutos. Palavras-chave: Pernambuco Tridimensional, modelo digital, análise de risco, geoprocessamento. Rupture Simulation of São Bento do Unas’s Dam using HEC-RAS Software A B S T R A C TThe damage associated with dam rupture is enormous, and must be avoided at all costs, as it can cause loss of human life. Therefore, several studies are carried out before its construction in order to avoid future disasters. Among them, we highlight the determination of the areas affected by a hypothetical rupture of the dam. This article presents the result of the simulation of rupture of the São Bento do Una Dam, located in the municipality of the same name in the interior of Pernambuco, using the one-dimensional model of non-permanent flow. The geometry of the study area was used as a basis, elaborated using the QGIS software through the analysis of digital terrain models, made available by the Pernambuco Three-Dimensional Program (PE3D), and exported to the HEC-RAS software. From the results, the affected area, water speed and depth were provided, and then maps were created in order to contribute to studies for contingency plans and risk mitigation. It was found that the elapsed time for the rupture to reach its final geometry was 56 minutes after the start of the simulation. The highest outlet flow from the reservoir occurs in the 56th minute, where 6672.72 m³ / s of water is expelled out of the reservoir, decreasing as the water level approaches the lower level of the breach gap. The time taken by water to reach the city of São Bento do Una, located about 17 km from the dam, was approximately 1 hour and 50 minutes.Keywords: Pernambuco three-dimensional, digital model, risk analysis, geoprocessing.

Referência(s)